硅烷改性聚氨酯密封膠膠料的挺性
2025-05-26
推薦新聞
MS密封膠高壓膠管內膠硬度
2025-05-26
丁基防水嵌縫膠的力學性能
2025-05-26
新型高溫高壓丁基防水嵌縫膠膠筒
2025-05-25
新型高溫高壓硅烷改性聚氨酯密封膠配方設計...
2025-05-25
MS密封膠粘結面未遭受破壞時的初始試驗
- 發布時間 : 2025-2-19 17:10:10
- Views:
(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.
MS密封膠粘結面未遭受破壞時的初始試驗
(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.
- 發布時間 : 2025-2-19 17:10:10
- Views:
Information
預測試
(1)在現場將加載裝置安裝在待測MS密封膠側面，高度宜在玻璃板塊高度中點。安裝位置應與有限元分析時一致。
(2)力傳感器、位移傳感器置零，分級施加荷載至測試荷載，每級荷載維持10s,測試荷載維持1 mimo測量記錄各級荷載、玻璃和鋁框間的相對位移。
(3)重復以上試驗過程，并檢查二次變形值差是否過大。
(4)故意切穿MS密封膠接縫(切割長度逐步增加)，在切穿處重復上述加荷試驗步驟，以確定MS密封膠遭到破壞的初始試驗撓度/fD和切割長度乙。MS密封膠縫的切割長度乙以加載點處出現明顯的撓度變化為準。
(5)重復上述試驗步驟以確定集中荷載值、MS密封膠粘結面未遭受破壞時的初始試驗撓度MS密封膠遭受破壞時的初始試驗撓度/fD和相應的故意切割長度。
正式檢測
(1)對其它玻璃分格相同、MS密封膠規格和種類相同的待測MS密封膠，按上述預測試試驗步驟進行試驗，測量MS密封膠的撓度變化。
(2)如MS密封膠粘結面質量存在外觀缺陷，加載點應布置在缺陷處附近。
(3)試驗過程中出現撓度超過初始測定撓度/fD時，應對撓度增加的原因進行分析。排除非粘結面破壞機理等因素。
檢測結果判定
如MS密封膠的撓度未超過初始試驗撓度可判定粘結面質量合格。http://hbxqtax.com/
Scan the QR code to read on your phone
+86-
13573398725
sdyuantai@163.com
搜索